欧能达主营YT无机活性微晶保温砂浆,YT无机改性保温材料系统,杭州外墙保温材料,杭州无机保温砂浆等!   联系我们
杭州欧能达建筑材料有限公司
24小时服务热线:0571-86551319
首页: 资讯中心 >> 行业资讯

资讯中心 News

产品介绍

不同住宅装修怎么样选择保温装饰一体板
不同住宅装修怎么样选择保温装饰一体板
文章来源:本站原创  作者:网站管理员  浏览:1 更新时间:2019-12-02 07:38:19

 为大家介绍不同的住宅对保温装饰一体板的要求:

 
  1.高度大于等于100m的建筑,其保温材料的燃烧性能应为A级。保温装饰一体板厂家是置于建筑物墙体表面的保温及装饰系统保温效果优秀并且长期,热桥作用少,节能保温效果好。
  2.高度大于等于60m小于100m的建筑,其保温材料的燃烧性能不应低于B2级。当采用B2级保温材料时,每层应设置水平防火隔离带。
 
  3.高度大于等于24m小于60m的建筑,其保温材料的燃烧性能不应低于B2级。当采用B2级保温材料时,每三层应设置水平防火隔离带。
 
  其他民用建筑应符合以下:
 
  1.高度大于等于50m的建筑,其保温材料的燃烧性能应为A级。
 
  2.高度大于等于24m小于50m的建筑,其保温材料的燃烧后性能不应低于B1级。其中,当采用B1级保温材料时,每两层应设置水平防火隔离带。
 
  3.高度小于24m的建筑,其保温材料的燃烧性能不应低于B2级。其中,当采用B2级保温材料时,每层应设置水平防火隔离带。 防护层 应采用不燃或难燃材料做防火层,防护层应将保温材料完全覆盖。保温装饰一体板 首层的防护层厚度不应小于6mm,其他层不应小于3mm. 防火隔离带 按本规定需要设置防火隔离带时,防火隔离带应采用A1(A)级保温材料沿窗口上沿位置与基层墙面全面积粘贴,高度宜与保温装饰一体板的宽度一致,且应不小于300m,竖缝填缝材料应采用A1(A)级同质材料。 防火隔离措施 保温装饰一体板使用可燃保温材料时,当保温材料表面及侧面均采用玻纤网格布增强聚合物砂浆或其它无机非金属材料防护层包裹(防护层厚度不小于3mm)等防火处理措施后可适当提高其燃烧性能等级。
 

To introduce different residential insulation decoration of one board requirements: 1. If the height of the building is more than or equal to 100m, the burning performance of the insulation material should be a class. Heat preservation and decoration one-piece board factory is placed in the building wall insulation and decoration system insulation effect is excellent and long-term, Thermal bridge, less role, energy-saving insulation effect. 2. For buildings with a height of 60m or less than 100m, the combustion performance of the insulation material shall not be lower than grade B2. When B2 class insulation material is used, each layer shall be provided with a horizontal fire-proof isolation belt. 3. If the height of the building is greater than or equal to 24m and less than 60m, the combustion performance of the insulation material should not be lower than grade B 2. When B2 class insulation material is used, a horizontal fire-proof isolation belt should be installed on every third floor. Other civil buildings shall conform to the following: 1. If the height of the building is greater than or equal to 50 meters, the burning performance of the insulation material should be a class. 2. For buildings with a height of 24M or less than 50m, the post-combustion performance of the insulation material shall not be lower than Grade B1. Among them, when using B1 class insulation material, every two layers should be set up level fire-proof isolation belt. 3. For buildings less than 24m in height, the flammability of the insulation material shall not be lower than grade B2. Among them, when using B2 class insulation material, each layer should be set up level fire-proof isolation belt. Protective Layer, should use non-combustible or fire-resistant materials as a fire layer, protective layer should be completely covered with thermal insulation materials. Insulation decorative one board, the first layer of the protective layer thickness should not be less than 6mm, the other layer should not be less than 3mm. The fire-proof isolation belt shall be pasted with a 1A class thermal insulation material along the upper edge of the window and the base wall surface in an all-round way, and the height shall be consistent with the width of the thermal insulation decorative one-piece Board And should not be less than 300m, vertical joint materials should be used A1A homogeneous material. Fire insulation measures, Thermal Insulation Decorative one-piece Board when using combustible thermal insulation materials, when the surface and side of thermal insulation material are treated with fire protection measures such as Glass Fiber Mesh cloth reinforced polymer mortar or other inorganic non-metallic material protective coating thickness not less than 3mm, its combustion performance can be properly improved.

Tag:
上一篇:没有了
下一篇:外墙柔性腻子施工时要注意哪些事项